Abstract
This research proposes a method for optimizing process performance; the method involves the use of multiple quality characteristics, fuzzy logic, and radial basis function neural networks (RBFNNs). In the method, each quality characteristic is transformed into a signal-to-noise ratio, and all the ratios are then provided as inputs to a fuzzy model to obtain a single comprehensive output measure (COM). The RBFNNs are used to generate a full factorial design. Finally, the average COM values are calculated for different factor levels, where for each factor, the level that maximizes the COM value is identified as the optimal level. Three case studies are presented for illustrating the method, and for all of them, the proposed method affords the largest total anticipated improvements in multiple quality responses compared with previously used methods, including the fuzzy, grey-Taguchi, Taguchi, and principal component analysis methods. The main advantages of the proposed method are its effectiveness in obtaining global optimal factor levels, its applicability and the requirement of less computational effort, and its efficiency in improving performance. In conclusion, the proposed method may enable practitioners optimize process performance by using multiple quality characteristics.
Similar content being viewed by others
References
Almonacid F, Rus C, Pérez-Higueras P, Hontoria L (2011) Calculation of the energy provided by a PV generator. comparative study: conventional methods vs. artificial neural networks. Energy 36(1):375–384
Al-Refaie A (2010) A grey-DEA approach for solving the multi-response problem in Taguchi method. J Eng Manuf 224(1):147–158
Al-Refaie A (2011) Optimizing correlated QCHs using principal components analysis and DEA techniques. Prod Plan Control 22(07):676–689
Al-Refaie A (2013) Optimization of multiple responses in the Taguchi method using fuzzy regression. Artif Intell Eng Des Anal Manuf 28:99–107
Al-Refaie A (2014a) A proposed satisfaction model to optimize process performance with multiple quality responses in the Taguchi method. J Eng Manuf 228(2):291–301
Al-Refaie A (2014b) Optimizing the performance of the tapping and stringing process for photovoltaic panel production. Int J Manag Sci Eng Manag. doi:10.1080/17509653.2014.974887
Al-Refaie A (2014c) Optimizing performance of low-voltage cables’ process with three quality responses using fuzzy goal programming. HKIE Trans 21(3):1–21
Al-Refaie A (2014d) Applying process analytical technology framework to optimize multiple responses in wastewater treatment process. J Zhejiang Univ Sci A 15(5):374–384
Al-Refaie A (2015) Optimizing multiple quality responses in the Taguchi method using fuzzy goal programming: modeling and applications. Int J Intell Syst 30(6):651–675
Al-Refaie A, Li M-H (2011) Optimizing the performance of plastic injection molding using weighted additive model in goal programming. Int J Fuzzy Syst Appl 22(07):676–689
Al-Refaie A, Wu T-H, Li M-H (2009) Data envelopment analysis approaches for solving the multi response problem in the Taguchi method. Artif Intell Eng Des Anal Manuf 23:159–173
Al-Refaie A, Rawabdeh I, Alhajj R, Jalham I (2012) A fuzzy multiple regression approach for optimizing multiple responses in the Taguchi method. Int J Fuzzy Syst Appl 3(2):14–35
Al-Refaie A, Diabat A, Li MH (2014) Optimizing tablets’ quality with multiple responses using fuzzy goal programming. J Process Mech Eng 228(2):115–126
Asiltürk İ, Çunkaş M (2011) Modeling and prediction of surface roughness in turning operations using artificial neural network and multiple regression method. Expert Syst Appl 38(5):5826–5832
Azadeh A, Sheikhalishahi M, Asadzadeh S (2011) A flexible neural network-fuzzy data envelopment analysis approach for location optimization of solar plants with uncertainty and complexity. Renew Energy 36:3394–3401
Bose PK, Deb M, Banerjee R, Majumder A (2013) Multi objective optimization of performance parameters of a single cylinder diesel engine running with hydrogen using a Taguchi-fuzzy based approach. Energy 63(15):375–386
Çakıroğlu R, Acır A (2013) Optimization of cutting parameters on drill bit temperature in drilling by Taguchi method. Measurement 46(9):3525–3531
Chen T (2015) An efficient and effective fuzzy collaborative intelligence approach for cycle time estimation in wafer fabrication. Int J Intell Syst 30:620–650
Chen SX, Gooi HB, Wang MQ (2013) Solar radiation forecast based on fuzzy logic and neural networks. Renew Energy 60:195–201
Dasgupta K, Singh DK, Sahoo DK, Anitha M, Awasthi A, Singh H (2014) Application of Taguchi method for optimization of process parameters in decalcification of samarium–cobalt intermetallic powder. Sep Purif Technol 124(18):74–80
de Pontes FJ, Paiva AP, Balestrassi PP, da Ferreira JR, Silva MB (2012) Optimization of radial basis function neural network employed for prediction of surface roughness in hard turning process using Taguchi’s orthogonal arrays. Expert Syst Appl 39(9):7776–7787
Furtuna R, Curteanu S, Leon F (2011) An elitist non-dominated sorting genetic algorithm enhanced with a neural network applied to the multi-objective optimization of a polysiloxane synthesis process. Eng Appl Artif Intell 24:772–785
Gupta A, Singh H, Aggarwal A (2011) Taguchi-fuzzy multi output optimization (MOO) in high speed CNC turning of AISI P-20 tool steel. Expert Syst Appl 38:6822–6828
Javan DS, Mashhadi HR, Rouhani M (2013) A fast static security assessment method based on radial basis function neural networks using enhanced clustering. Electr Power Energy Syst 44(1):988–996
Li M-H, Al-Refaie A, Yang CY (2008) DMAIC approach to improve the capability of SMT solder printing process. IEEE Trans Electron Packag Manuf 31(2):126–133
Lilly JH (2010) Fuzzy control and identification, 3rd edn. Wiley, Hoboken
Lin H-C, Su C-T, Wang C-C, Chang B-H, Juang R-C (2012) Parameter optimization of continuous sputtering process based on Taguchi methods, neural networks, desirability function, and genetic algorithms. Expert Syst Appl 39(17):12918–12925
Mandic K, Delibasic B, Knezevic S, Benkovic S (2014) Analysis of the financial parameters of Serbian banks through the application of the fuzzy AHP and TOPSIS methods. Econ Model 43:30–37
Marvuglia A, Messineo A, Nicolosi G (2014) Coupling a neural network temperature predictor and a fuzzy logic controller to perform thermal comfort regulation in an office building. Build Environ 72:287–299
Moosavi M, Soltani N (2013) Prediction of the specific volume of polymeric systems using the artificial neural network-group contribution method. Fluid Phase Equilib 356:176–184
Muthuramalingam T, Mohan B (2014) Application of Taguchi-grey multi responses optimization on process parameters in electro erosion. Measurement 58:495–502
Otebolaku AM, Andrade MT (2015) Context-aware media recommendations for smart devices. J Ambient Intell Humaniz Comput 6(1):13–36
Peng X, Li Q, Wang K (2014) Core axial power shape reconstruction based on radial basis function neural network. Ann Nucl Energy 73:339–344
Sivasakthivel T, Murugesan K, Thomas HR (2014) Optimization of operating parameters of ground source heat pump system for space heating and cooling by Taguchi method and utility concept. Appl Energy 116:76–85
Sun J-H, Hsueh B-R (2011) Optical design and multi-objective optimization with fuzzy method for miniature zoom optics. Opt Lasers Eng 49:962–971
Sun J-H, Fang Y-C, B-R Hsueh (2012) Combining Taguchi with fuzzy method on extended optimal design of miniature zoom optics with liquid lens. Optik 123(19):1768–1774
Tatar A, Shokrollahi A, Mesbah M, Rashid S, Arabloo M, Bahadori A (2013) Implementing radial basis function networks for modeling CO2-reservoir oil minimum miscibility pressure. J Nat Gas Sci Eng 15:82–92
Tsai T (2014) Improving the fine-pitch stencil printing capability using the Taguchi method and Taguchi fuzzy-based model. Robot Comput Integr Manuf 27:808–817
Wu H-C, Chen T (2015) CART–BPN approach for estimating cycle time in wafer fabrication. J Ambient Intell Humaniz Comput 6:57–67
Xia C, Wang J, McMenemy K (2010) Short, medium and long term load forecasting model and virtual load forecaster based on radial basis function neural networks. Electr Power Energy Syst 32(7):743–750
Zăvoianu A-C, Bramerdorfer G, Lughofer E, Silber S, Amrhein W, Klement EP (2013) Hybridization of multi-objective evolutionary algorithms and artificial neural networks for optimizing the performance of electrical drives. Eng Appl Artif Intell 26:1781–1794
Zolgharnein J, Asanjrani N, Bagtash M, Azimi G (2014) Multi-response optimization using Taguchi design and principle component analysis for removing binary mixture of alizarin red and alizarin yellow from aqueous solution by nano c-alumina. Spectrochim Acta Part A Mol Biomol Spectrosc 126:291–300
Author information
Authors and Affiliations
Corresponding author
Rights and permissions
About this article
Cite this article
Al-Refaie, A., Chen, T., Al-Athamneh, R. et al. Fuzzy neural network approach to optimizing process performance by using multiple responses. J Ambient Intell Human Comput 7, 801–816 (2016). https://doi.org/10.1007/s12652-015-0340-5
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12652-015-0340-5