Trial Surface-Property Prediction in End-Mill Operation

Hirohisa Narita; Keiichi Shirase; Eiji Arai; Hideo Fujimoto

doi:10.20965/ijat.2010.p0229

single-au.php

« previous

IJAT Vol.4 No.3 pp. 229-234

doi: 10.20965/ijat.2010.p0229

(2010)

Paper:

Views over last 60 days: 392

Trial Surface-Property Prediction in End-Mill Operation

Hirohisa Narita^1, Keiichi Shirase^2, Eiji Arai^3, and Hideo Fujimoto^4

^*1School of Health Sciences, Fujita Health University, 1-98 Dengakugakubo, Kutsukake-cho, Toyoake, Aichi 470-1192, Japan

^*2Department of Mechanical Engineering, Kobe University, 1-1 Rokko-dai, Nada-ku, Kobe 657-8501, Japan

^*3Department of Manufacturing Science, Graduate School of Engineering, Osaka University, 2-1, Yamada-oka, Suita, Osaka 565-0871, Japan

^*4Graduate School of Engineering, Nagoya Institute of Technology, Gokiso-cho, Showa-ku, Nagoya, Aichi 466-8555, Japan

Received:

December 15, 2009

Accepted:

January 11, 2010

Published:

May 5, 2010

Keywords:

end mill, surface properties, cutting force, runout, tool vibration

Abstract

Because surface precision is an important factor in machined surfaces, we propose a model for predicting surface properties in end-mill operation. Prediction considers cutting edges including a cutting tool movement and rotation and cutter runout and vibration. Experiments confirmed the model’s feasibility.

Cite this article as:

H. Narita, K. Shirase, E. Arai, and H. Fujimoto, “Trial Surface-Property Prediction in End-Mill Operation,” Int. J. Automation Technol., Vol.4 No.3, pp. 229-234, 2010.

Data files:

References

[1] H. Narita, L. Y. Chen, H. Fujimoto, K. Shirase, and E. Arai, “Trial-Less Machining Using Virtual Machining Simulator for Ball End Mill Operation,” Int. J. of Jpn Soc. of Mech. Eng., (Series C), Vol.49, No.1, pp. 50-55, 2006.
[2] E. Budak and Y. Altintas, “Analytical Prediction of Chatter Stability in Milling – Part I: General Formulation. Trans. ASME Journal of Dynamic Systems,” Measurement and Control, Vol.120, No.1, pp. 22-30, 1998.
[3] J. H. Ko and D. W. Cho, “3D Ball End Mill Force Model Using Instantaneous Cutting Force Coefficients,” Trans. ASME J. of Manufacturing Science and Engineering, Vol.127, No.1, pp. 1-12, 2005.
[4] H. Narita, K. Shirase, H. Wakamatsu, and E. Arai, “Pre-Process Evaluation of EndMilling Operation Using Virtual Machining Simulator,” Int. J. of Jpn Soc. of Mech. Eng., (Series C), Vol.43, No.2, pp. 492-497, 2000.
[5] W. H. Press, S. A. Teukolsky, W. T. Vetterling and B. P. Flannery, “Numerical Recipes in C,” Cambridge University Press, 1988.
[6] National Instrument home page
http://www.ni.com/

This article is published under a Creative Commons Attribution-NoDerivatives 4.0 Internationa License.

[1] [1] H. Narita, L. Y. Chen, H. Fujimoto, K. Shirase, and E. Arai, “Trial-Less Machining Using Virtual Machining Simulator for Ball End Mill Operation,” Int. J. of Jpn Soc. of Mech. Eng., (Series C), Vol.49, No.1, pp. 50-55, 2006.

[2] [2] E. Budak and Y. Altintas, “Analytical Prediction of Chatter Stability in Milling – Part I: General Formulation. Trans. ASME Journal of Dynamic Systems,” Measurement and Control, Vol.120, No.1, pp. 22-30, 1998.

[3] [3] J. H. Ko and D. W. Cho, “3D Ball End Mill Force Model Using Instantaneous Cutting Force Coefficients,” Trans. ASME J. of Manufacturing Science and Engineering, Vol.127, No.1, pp. 1-12, 2005.

[4] [4] H. Narita, K. Shirase, H. Wakamatsu, and E. Arai, “Pre-Process Evaluation of EndMilling Operation Using Virtual Machining Simulator,” Int. J. of Jpn Soc. of Mech. Eng., (Series C), Vol.43, No.2, pp. 492-497, 2000.

[5] [5] W. H. Press, S. A. Teukolsky, W. T. Vetterling and B. P. Flannery, “Numerical Recipes in C,” Cambridge University Press, 1988.

[6] [6] National Instrument home page
http://www.ni.com/

Trial Surface-Property Prediction in End-Mill Operation

Hirohisa Narita*1, Keiichi Shirase*2, Eiji Arai*3, and Hideo Fujimoto*4

Hirohisa Narita^1, Keiichi Shirase^2, Eiji Arai^3, and Hideo Fujimoto^4