Top > JRM > Identification of Dominant Error Force Component in Hydraulic ...

single-rb.php

JRM Vol.24 No.1 pp. 95-104
doi: 10.20965/jrm.2012.p0095
(2012)

Paper:

Views over last 60 days: 972

Identification of Dominant Error Force Component in Hydraulic Pressure Reading for External Force Detection in Construction Manipulator

Mitsuhiro Kamezaki*, Hiroyasu Iwata**,
and Shigeki Sugano***

*Department of Modern Mechanical Engineering, School of Creative Science and Engineering, Waseda University, 17 Kikui-cho, Shinjuku-ku, Tokyo 162-0044, Japan

**Waseda Institute for Advanced Study (WIAS), Waseda University, 1-6-1 Nishi Waseda, Shinjuku-ku, Tokyo 169-8050, Japan

***Department of Modern Mechanical Engineering, School of Creative Science and Engineering, Waseda University, 3-4-1 Okubo, Shinjuku-ku, Tokyo 169-8555, Japan

Received:
April 30, 2011
Accepted:
August 16, 2011
Published:
February 20, 2012
Creative Commons License
Keywords:
construction machinery, external force detection, hydraulic sensor, error force identification
Abstract
The purpose of this paper is to develop a fundamental external-force-detection framework for construction manipulators. Such an industrial application demands the practicality that satisfies detection requirements such as the accuracy and robustness while ensuring (i) a low cost, (ii) wide applicability, and (iii) a simple detection algorithm. For satisfying (i) and (ii), our framework first adopts a hydraulic sensor as a force sensor. However, hydraulic-pressure readings essentially include error force components. These components depend strongly on the joint kinetic state and differ in the identification difficulty owing to a nonlinear and uncertain hydromechanical system. For satisfying (ii) and (iii), our framework thus focuses on the dominant error-force components classified by the control input states, such as self-weight, cylinder driving, and oscillating forces, and identifies and removes them by using a theoreticalmodel, an experimental estimation, and a waveform analysis without complex modeling, respectively. Experiments were conducted using an instrumented hydraulic arm system. The results of a no-load task indicate that our framework greatly lowers the threshold to determine the on-off state of external force application, independent of the joint kinetic states. The results of an on-load task confirm that our framework robustly identifies the off states in which an external force is not applied to the hydraulic cylinder.
Cite this article as:
M. Kamezaki, H. Iwata, and S. Sugano, “Identification of Dominant Error Force Component in Hydraulic Pressure Reading for External Force Detection in Construction Manipulator,” J. Robot. Mechatron., Vol.24 No.1, pp. 95-104, 2012.
Data files:
References
  1. [1] M. Kamezaki, H. Iwata, and S. Sugano, “Operator Support System based on Primitive Static States in Intelligent Operated-Work Machines,” Advanced Robotics, Vol.23, No.10, pp. 1281-1297, 2009.
  2. [2] M. Kamezaki, H. Iwata, and S. Sugano, “Primitive Static States for Intelligent Operated-Work Machines,” in Proc. of IEEE Int. Conf. on Robotics and Automation, pp. 1334-1339, 2009.
  3. [3] M. Kamezaki, H. Iwata, and S. Sugano, “Development of an Operation Skill-Training Simulator for Double-Front Work Machine – Training Effect for House Demolition Work –,” J. of Robotics and Mechatronics, Vol.20, No.4, pp. 602-609, 2008.
  4. [4] D.-S. Han, J.-M. Ha, and G.-J. Han, “Development of Many-Angular Pin Type Load Cell for a Overload Limiter of a Movable Crane,” Key Engineering Materials, Vol.413/414, pp. 291-298, 2009.
  5. [5] H. E. Merritt, “Hydraulic Control Systems,” New York: Wiley, 1967.
  6. [6] M. Tahmeen, H. Yamada, H. Kato, K. Maehata, and T. Muto, “A Study on Simulation of Hydraulic Construction Machine,” in Proc. of SICE Annual Conf., pp. 856-861, 2003.
  7. [7] F. Behi and D. Tesar, “Parametric Identification for Industrial Manipulators Using Experimental Model Analysis,” IEEE Trans. on Robotics and Automation, Vol.7, No.5, pp. 642-652, 1991.
  8. [8] B. Yao, F. Bu, J. Reedy, and G. T.-C. Chiu, “Adaptive robust motion control of single-rod hydraulic actuators: theory and experiments,” IEEE/ASME Trans. on Mechatronics, Vol.5, No.1, pp. 79-91, 2000.
  9. [9] M. Kamezaki, H. Iwata, and S. Sugano, “Development of a Dual Robotic Arm System to Evaluate Intelligent System for Advanced Construction Machinery,” in Proc. of 2010 IEEE/ASME Int. Conf. on Advanced Intelligent Mechatronics, pp.1299-1304, 2010.
  10. [10] D. Ma and J.M. Hollerbach, “Identifying mass parameters for gravity compensation and automatic torque sensor calibration,” in Proc. of IEEE Int. Conf. on Robotics and Automation, pp. 661-666, 1996.
  11. [11] S. Tafazoli, P. D. Lawrence, S. E. Salcudean, D. Chan, S. Bachmann, and C. W. de Silva, “Parameter estimation and friction analysis for a mini excavator,” in Proc. of IEEE Int. Conf. on Robotics and Automation, pp. 329-334, 1996.
  12. [12] C. H. An, C. G. Atkkeson, and J. M. Hollerbach, “Estimation of Inertial Parameters of Rigid Body Links of Manipulators,” in Proc. of 24th Conf. on Decision and Control, pp. 990-995, 1985.
  13. [13] S. Tafazoli, P. D. Lawrence, and S. E. Salcudean, “Identification of Inertial and Friction Parameter for excavator Arms,” IEEE Trans. on Robotics and Automation, Vol.25, No.5, pp. 966-971, 1999.
  14. [14] E. G. Papadopoulos and G. C. Chasparis, “Analysis and Modelbased Control of Servomechanism with Friction,” in Proc. of IEEE/RSJ Int. Conf. on Intelligent Robot and Systems, pp. 2109-2114, 2002.

Creative Commons License  This article is published under a Creative Commons Attribution-NoDerivatives 4.0 Internationa License.

Copyright© 2012 by Fuji Technology Press Ltd. and Japan Society of Mechanical Engineers. All right reserved.

*This site is desgined based on HTML5 and CSS3 for modern browsers, e.g. Chrome, Firefox, Safari, Edge, Opera.

Last updated on Apr. 22, 2024