Abstract
This work includes the analysis and evaluation of surgically removed wings from Manduca sexta hawkmoth and the fabrication and testing of moth-like wings for the eventual goal of developing a flapping wing micro air vehicle. The natural and manufactured wings are compared in three main characteristics, their distribution of mass, their flexural stiffness, and their camber. Previous results indicate that if these three properties can be mimicked, manufactured wings could produce similar flight properties to the natural wings. Wings are manufactured based on templates created from three different moths. Additionally, three different materials are used for fabricating the membrane, Icarex Ripstop Fabric, Mylar Film, and Kapton Film. Strips of unidirectional carbon fiber are used to mimic the venation structure. Wings manufactured from Icarex and Kapton replicated the mass of the natural wings. However, all manufactured wings are far stiffer than the natural ones. Icarex retains its camber the best.
This is a preview of subscription content, log in via an institution to check access.
Access this chapter
Tax calculation will be finalised at checkout
Purchases are for personal use only
References
Moses, K.C., Michaels, S.C., Willis, M., Quinn, R.D.: Artificial Manduca sexta forewings for flapping-wing micro aerial vehicles: how wing structure affects performance. Bioinspiration Biomimetics 12(5) (2017)
Michaels, S.C., et al.: Biomimicry of the Manduca sexta forewing using SRT protein complex for FWMAV development. In: Wilson, S.P., Verschure, P.F.M.J., Mura, A., Prescott, T.J. (eds.) LIVINGMACHINES 2015. LNCS (LNAI), vol. 9222, pp. 86–91. Springer, Cham (2015). https://doi.org/10.1007/978-3-319-22979-9_8
Moses, K.C., Prigg, D., Weisfeld, M., Bachmann, R.J., Willis, M., Quinn, R.D.: Simulating flapping wing mechanisms inspired by the Manduca sexta hawkmoth. In: Vouloutsi, V., et al. (eds.) Living Machines 2018. LNCS (LNAI), vol. 10928, pp. 326–337. Springer, Cham (2018). https://doi.org/10.1007/978-3-319-95972-6_35
Fearing, R.S., Chiang, K.H., Dickenson, M.H., Pick, D.L., Sitti, M., Yan, J.: Wing transmission for a micromechanical flying insect. In: Proceedings 2000 ICRA. Millennium Conference. IEEE International Conference on Robotics and Automation. Symposia Proceedings (2000)
Yan, J., Wood, R.J., Avadhanula, S., Sitti, M., Fearing, R.S.: Towards flapping wing control for a micromechanical flying insect. In: IEEE International Conference on Robotics and Automation (2001)
Wood, R.J., Avadhanula, S., Sahai, R., Steltz, E., Fearing, R.S.: Microrobot design using fiber reinforced composites. J. Mech. Des. 30(5)
Wood, R.J.: The first takeoff of a biologically inspired at-scale robotic insect. IEEE Trans. Rob. 24(2), 341–347 (2008)
Ramezani, A., Chung, S.-J., Hutchinson, S.: A biomimetic robotic platform to study flight specializations of bats. Sci. Robot. 2(3) (2017)
Bunget, G., Seelecke, S.: BATMAV: a biologically inspired micro air vehicle for flapping flight: kinematic modeling. In: SPIE Smart Structures and Materials Nondestructive Evaluation and Health Monitoring, vol. 6928 (2008)
Keennon, M., Klingebiel, K., Won, H.: Development of the nano hummingbird: a tailless flapping wing micro air vehicle. In: 50th AIAA Aerospace Sciences Meeting Including the New Horizons Forum and Aerospace Exposition (2012)
Nguyen, Q.V., Park, H.C., Goo, N.S., Byun, D.: Characteristics of a beetle’s free flight and a flapping-wing system that mimics beetle flight. J. Bionic Eng. 7(1), 77–86 (2010)
Combes, S.A., Daniel, T.L.: Into thin air: contributions of aerodynamic and inertial-elastic forces to wing bending in the hawkmoth Manduca sexta. J. Exp. Biol. 206, 2999–3006 (2003)
Combes, S.A., Daniel, T.L.: Flexural stiffness in insect wings I. Scaling and the influence of wing venation. J. Exp. Biol. 206(17), 2979–2987 (2003)
Combes, S.A., Daniel, T.L.: Flexural stiffness in insect wings II. Spatial distribution and dynamic wing bending. J. Exp. Biol. 206(17), 2989–2997 (2003)
Mountcastle, A.M., Daniel, T.L.: Aerodynamic and functional consequences of wing compliance. In: Taylor, G.K., Triantafyllou, M.S., Tropea, C. (eds.) Animal Locomotion, pp. 311–320. Springer, Heidelberg (2010). https://doi.org/10.1007/978-3-642-11633-9_25
Mountcastle, A.M., Combes, S.A.: Wing flexibility enhances load-lifting capabilities in bumblebees. Proc. R. Soc. B Biol. Sci.
Mountcastle, A.M.: Structural dynamics and aerodynamics of flexible wings in insect flight, dissertation (2010)
O’Hara, R.P., Palazotto, A.N.: The morphological characterization of the forewing of the Manduca sexta species for the application of biomimetic flapping wing micro air vehicles. Bioinspiration Biomimetics 7(4) (2012)
O’Hara, R.P.: The characterization of material properties and structural dynamics of the Manduca sexta forewing for application to flapping wing micro air vehicle design, dissertation (2012)
Tobias, A.P.: Experimental methods to characterize nonlinear vibration of flapping wing micro air vehicles, thesis (2007)
Sims, T.W.: A structural dynamic analysis of a Manduca sexta forewing, thesis (2010)
Dudley, R.: The Biomechanics of Insect Flight: Form, Function, Evolution. Princeton University Press, Princeton (2000)
Author information
Authors and Affiliations
Corresponding author
Editor information
Editors and Affiliations
Rights and permissions
Copyright information
© 2019 Springer Nature Switzerland AG
About this paper
Cite this paper
Weisfeld, M., Moses, K., Prigg, D., Bachmann, R., Willis, M., Quinn, R. (2019). Manufacturing Artificial Wings Based on the Manduca sexta Hawkmoth. In: Martinez-Hernandez, U., et al. Biomimetic and Biohybrid Systems. Living Machines 2019. Lecture Notes in Computer Science(), vol 11556. Springer, Cham. https://doi.org/10.1007/978-3-030-24741-6_23
Download citation
DOI: https://doi.org/10.1007/978-3-030-24741-6_23
Published:
Publisher Name: Springer, Cham
Print ISBN: 978-3-030-24740-9
Online ISBN: 978-3-030-24741-6
eBook Packages: Computer ScienceComputer Science (R0)