Abstract
The geometrical accuracy and the surface quality of sheet metal parts as well as the tool wear are influenced by process parameters and by static and dynamic interactions between the press and the tool. Therefore the qualitative characterization of the machine behavior is of high importance for both press manufacturers and press operators. Within research project (Behrens et al. in Entwicklung und Erweiterung standardisierter Messverfahren zur statischen und dynamischen Pressenvermessung. Final Report of the AiF Research Project 13742 N, 2005), a procedure for the measurement of the static machine behavior has been developed, which for the first time allows the standardized measurement of the ram deflection and the bolster plate deflection along with previously standardized characteristic values. The determination of the procedure as measurement directions and the automated evaluation of the measurements ensure not only reproducible results but also easy comparison of two machines. Additionally a new procedure for the measurement of the dynamic press behavior has been standardized which allows the comparison of the static and the dynamic characteristic values.
Similar content being viewed by others
References
Behrens B-A, Brecher C, Hork M, Werbs M (2005) Entwicklung und Erweiterung standardisierter Messverfahren zur statischen und dynamischen Pressenvermessung. Final Report of the AiF Research Project 13742 N
DIN 55 189 T.1 und T.2 (1988) Ermittlung von Kennwerten für Pressen der Blechverarbeitung bei statischer Belastung. Beuth, Berlin
VDI 3145 Blatt 1 (1984) Pressen zum Kaltmassivumformen Mechanische und hydraulische Pressen. Verein Deutscher Ingenieure
Bogon P (1997) Stastische Genauigkeitskenngroßen von mechanischen Karoseriepressen. Blech Rohre Profile 6:44–51
Rühlicke I, Krüger K (1996) Hydraulische Prüfeinrichtung zur statischen und dynamischen Pressenuntersuchung. O + P Ölhydraulik und Pneumatik 40(2):126–130
Behrens B-A, Brecher C, Hork M, Werbs M (2005) Entwicklung eines aktiven Dämpfersystems zur Reduzierung des Werkzeugverschleißes von Schneidwerkzeugen. Final Report of the AiF Research Project 70 ZN
Derenthal M, Doege E, Großmann K, Krell M, Weck M, Wiemer H (2001) Reduction of tool wear by increase of machine damping. In: Second international conference and exhibition on design and production of dies and mold, Kusadasi
Derenthal M, Doege E, Großmann K, Krell M, Weck M, Wiemer H (2001) Einfluss der Dämpfungseigenschaften von weggebundenen Schnellläuferpressen auf den Werkzeugverschleiß. Final Report of the AiF Research Project Forschungsvorhaben AiF 11842 B
Behrens B-A, Marthiens O, Werbs M (2005) Electromagnetic dampening of the cutting shock on sheet metal presses. In: Advanced proceedings of the eight ICTP, Verona, Technology of Plasticity, pp 379–380
Bogon P, Wagener W (1992) Dynamische Federung von Exzenterpressen–Ergebnisse. Blech Rohre Profile 32(4):319–323
Doege E, Lange K (1980) Static and dynamic stiffness of presses and some effects on the accuracy of workpieces. Ann CIRP 29/1/1980:167–171
Author information
Authors and Affiliations
Corresponding author
Additional information
The project [1] was funded under number AiF 13742 N by the Arbeitsgemeinschaft industrieller Forschungsvereinigungen “Otto von Guericke” e.V. with budget funds from the German Federal Ministry of Economics.
Rights and permissions
About this article
Cite this article
Behrens, BA., Brecher, C., Hork, M. et al. New standardized procedure for the measurement of the static and dynamic properties of forming machines. Prod. Eng. Res. Devel. 1, 31–36 (2007). https://doi.org/10.1007/s11740-007-0005-0
Received:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s11740-007-0005-0