Abstract
In this study, we investigated the wetting transition of a moving meniscus in a grooved microchannel through a detailed parametric study based on measurement by an optical tool and μ-particle image velocimetry (PIV) to avoid the transition in designing the microchannel. The parameters investigated were pitch, flow rate, and height of a microchannel. The contact angle, contact speed, and interfacial pressure difference were analyzed according to the parameters. We found that the pitch is most effective, the flow rate is moderately effective, and the height is least effective on that. The height even does not affect the contact angle, because the solid–fluid interaction at the groove edge is stronger than the fluid–air interaction. As the critical correlation, the contact angle, which is dependent on the pitch and the flow rate, and the height affect the air pressure between the grooves, which governs the air penetration flux and mainly determines the wetting transition. Therefore, a powerful way to delay the wetting transition is to reduce the degree of air pressure variation, specifically with a low pitch and a tall height with a low flow rate. Eventually, understanding dominant input parameters in relation to the wetting transition will be very useful in the design stage of microfluidic applications.
Graphical Abstract
Similar content being viewed by others
References
Arkilic EB, Schmidt MA, Breuer KS (1997) Gaseous slip flow in long microchannels. J Microelectromech Syst 6:167–178
Bico J, Tordeux C, Quere D (2001) Rough wetting. EPL (Europhys Lett) 55:214
Bobji MS, Kumar SV, Asthana A, Govardhan RN (2009) Underwater sustainability of the “Cassie” state of wetting. Langmuir 25:12120–12126. doi:10.1021/la902679c
Bonn D, Eggers J, Indekeu J, Meunier J, Rolley E (2009) Wetting and spreading. Rev Mod Phys 81:739
Byun D, Kim J, Ko HS, Park HC (2008) Direct measurement of slip flows in superhydrophobic microchannels with transverse grooves. Phys Fluids 20:113601
Chen S, Tian Z (2010) Simulation of thermal micro-flow using lattice Boltzmann method with Langmuir slip model. Int J Heat Fluid Flow 31:227–235
Colin S, Lalonde P, Robert C (2004) Validation of a second-order slip flow model in rectangular microchannels. Heat Transf Eng 25:23–30
Dorrer C, Ruhe J (2007) Condensation and wetting transitions on microstructured ultrahydrophobic surfaces. Langmuir 23:3820–3824
Eddings MA, Gale BK (2006) A PDMS-based gas permeation pump for on-chip fluid handling in microfluidic devices. J Micromech Microeng 16:2396
El Moctar AO, Aubry N, Batton J (2003) Electro-hydrodynamic micro-fluidic mixer. Lab Chip 3:273–280
Fowler J, Hyejin M, Chang-Jin K (2002) Enhancement of mixing by droplet-based microfluidics. In: The fifteenth IEEE international conference on micro electro mechanical systems, 2002, pp 97–100
Fuhr G, Hagedorn R, Muller T, Benecke W, Wagner B (1992) Microfabricated electrohydrodynamic (EHD) pumps for liquids of higher conductivity. J Microelectromech Syst 1:141–146
Gurka R, Liberzon A, Hefetz D, Rubinstein D, Shavit U (1999) Computation of pressure distribution using PIV velocity data. In: Workshop on particle image velocimetry
Hayes RA, Ralston J (1993) Forced liquid movement on low energy surfaces. J Colloid Interface Sci 159:429–438
Herminghaus S (2000) Roughness-induced non-wetting. EPL (Europhys Lett) 52:165
Huang J, Shu C, Chew Y (2009) Lattice Boltzmann study of droplet motion inside a grooved channel. Phys Fluids 21:022103
Jung Y, Bhushan B (2007) Wetting transition of water droplets on superhydrophobic patterned surfaces. Scr Mater 57:1057–1060
Kim TJ, Hidrovo C (2012) Pressure and partial wetting effects on superhydrophobic friction reduction in microchannel flow. Phys Fluids (1994-present) 24:112003
Kim DS, Lee K-C, Kwon TH, Lee SS (2002) Micro-channel filling flow considering surface tension effect. J Micromech Microeng 12:236
Kim Y, Choi W, Lee J (2011a) Water droplet properties on periodically structured superhydrophobic surfaces: a lattice Boltzmann approach to multiphase flows with high water/air density ratio. Microfluid Nanofluid 10(1):173–185. doi:10.1007/s10404-010-0658-4
Kim J, Byun D, Hong J (2011b) Novel method of generating water-in-oil (W/O) droplets in a microchannel with grooved walls. Biomicrofluidics 5:014106
Lafuma A, Quere D (2003) Superhydrophobic states. Nat Mater 2:457–460
Lemoff AV, Lee AP (2000) An AC magnetohydrodynamic micropump. Sens Actuators B: Chem 63:178–185
Li X-M, Reinhoudt D, Crego-Calama M (2007) What do we need for a superhydrophobic surface? A review on the recent progress in the preparation of superhydrophobic surfaces. Chem Soc Rev 36:1350–1368
Luo C, Xiang M, Liu X, Wang H (2011) Transition from Cassie–Baxter to Wenzel States on microline-formed PDMS surfaces induced by evaporation or pressing of water droplets. Microfluid Nanofluid 10(4):831–842. doi:10.1007/s10404-010-0714-0
Markov DA, Lillie EM, Garbett SP, McCawley LJ (2014) Variation in diffusion of gases through PDMS due to plasma surface treatment and storage conditions. Biomed Microdevices 16:91–96
Meinhart C, Prasad A, Adrian R (1993) A parallel digital processor system for particle image velocimetry. Meas Sci Technol 4:619
Meinhart CD, Wereley ST, Santiago JG (1999) PIV measurements of a microchannel flow. Exp Fluids 27:414–419
Merkel T, Bondar V, Nagai K, Freeman B, Pinnau I (2000) Gas sorption, diffusion, and permeation in poly (dimethylsiloxane). J Polym Sci Part B: Polym Phys 38:415–434
Nosonovsky M, Bhushan B (2007) Hierarchical roughness optimization for biomimetic superhydrophobic surfaces. Ultramicroscopy 107:969–979
Patankar NA (2004) Transition between superhydrophobic states on rough surfaces. Langmuir 20:7097–7102. doi:10.1021/la049329e
Patankar NA, Hu HH (1998) Numerical simulation of electroosmotic flow. Anal Chem 70:1870–1881
Peters A, Pirat C, Sbragaglia M, Borkent B, Wessling M, Lohse D, Lammertink R (2009) Cassie-Baxter to Wenzel state wetting transition: scaling of the front velocity. Eur Phys J E: Soft Matter Biol Phys 29:391–397
Polson NA, Hayes MA (2000) Electroosmotic flow control of fluids on a capillary electrophoresis microdevice using an applied external voltage. Anal Chem 72:1088–1092
Prasad A, Adrian R, Landreth C, Offutt P (1992) Effect of resolution on the speed and accuracy of particle image velocimetry interrogation. Exp Fluids 13:105–116
Randall GC, Doyle PS (2005) Permeation-driven flow in poly (dimethylsiloxane) microfluidic devices. Proc Natl Acad Sci USA 102:10813–10818
Rothstein JP (2010) Slip on superhydrophobic surfaces. Annu Rev Fluid Mech 42:89–109
Seemann R, Brinkmann M, Kramer E, Lange F, Lipowsky R (2005) Wetting morphologies at microstructured surfaces. Proc Natl Acad Sci USA 102:1848
Shah GJ, Ohta AT, Eric PYC, Wu MC (2009) EWOD-driven droplet microfluidic device integrated with optoelectronic tweezers as an automated platform for cellular isolation and analysis. Lab Chip 9:1732–1739
Sze A, Erickson D, Ren L, Li D (2003) Zeta-potential measurement using the Smoluchowski equation and the slope of the current-time relationship in electroosmotic flow. J Colloid Interface Sci 261:402–410
Toepke MW, Beebe DJ (2006) PDMS absorption of small molecules and consequences in microfluidic applications. Lab Chip 6:1484–1486
Walker SW, Shapiro B (2006) Modeling the fluid dynamics of electrowetting on dielectric (EWOD). J Microelectromech Syst 15:986–1000
Wang PJ, Chang CY, Chang ML (2004) Simulation of two-dimensional fully developed laminar flow for a magneto-hydrodynamic (MHD) pump. Biosens Bioelectron 20:115–121
West J et al (2002) Application of magnetohydrodynamic actuation to continuous flow chemistry. Lab Chip 2:224–230
Woolford B, Maynes D, Webb B (2009) Liquid flow through microchannels with grooved walls under wetting and superhydrophobic conditions. Microfluid Nanofluid 7:121–135. doi:10.1007/s10404-008-0365-6
Zhang J, Kwok DY (2006) Contact line and contact angle dynamics in superhydrophobic channels. Langmuir 22:4998–5004. doi:10.1021/la053375c
Zheng Q, Yu Y, Zhao Z (2005) Effects of hydraulic pressure on the stability and transition of wetting modes of superhydrophobic surfaces. Langmuir 21:12207–12212
Acknowledgments
This work was a part of a project entitled “Three-Dimensional Cloaking Meta-Materials by Developing Super-Fine Patterning Nano-Inkjet Technology”, funded by the National Research Foundation of Korea (NRF-2015R1A2A1A05001829) and was part of a project entitled “Core Technology Development for Hybrid Power Generation Based on Tidal Current Energy” funded by the Korea Institute of Ocean Science and Technology (PE99421). The authors thank Prof. Jongin Hong at Chung-Ang University for providing the information of the fabrication processes. The authors also thank Mr. Patrick Comiskey at the University of Illinois at Chicago for the valuable comments of this work.
Author information
Authors and Affiliations
Corresponding authors
Rights and permissions
About this article
Cite this article
Kim, J., Ko, J.H., Lee, J. et al. Parametric study of the wetting transition of a moving meniscus. J Vis 20, 111–123 (2017). https://doi.org/10.1007/s12650-016-0385-3
Received:
Revised:
Accepted:
Published:
Issue Date:
DOI: https://doi.org/10.1007/s12650-016-0385-3