Joel G. Amora
ABSTRACT
Embedded system is an emerging technology that can be applied to all areas. In this paper, the embedded system is designed to be used for easily interpreting the signals of the electrochemical immunosensor. NI myRIO was used as the key component of the embedded system. LabView was used to design the block diagram of the system. This paper is only limited to the design of the embedded circuits. The signals coming from the electrochemical immunosensor was mimic by inputting low voltage level similar to the output of the immunosensor. Based on the given threshold voltage level the system successfully interpret the presence of disease.
- Felix, F., and Angnes, L. April 2018. Electrochemical immunosensors -- A powerful tool for analytical applications. Biosensors and Bioelectronics, Vol. 102, 470--478.Google Scholar
Cross Ref
- Kokkinos, C., Economou, A., and Prodromidis, M. May 2016. Electrochemical immunosensors: Critical survey of different architectures and transduction strategies. TrAC Trends in Analytical Chemistry, Vol. 79, 88--105.Google ScholarCross Ref
- Raskin, D., Vassiliev, A., Samarin, V., Cabezas, D., Hiererra, S.E., and Kurniawan, Y. 2018. Procedia Computer Science, Vol. 135, 503--509.Google Scholar
- Moina, C., and Ybarra, G. 2012. Fundamentals and applications of immunosensors, Advances in Immunoassay Technology. Dr. Norman H. L. Chiu (Ed.). ISBN: 978-953-51-0440-7.Google Scholar
- Rodrigo, M.A.M. et al. 2014. HIV Biosensor -- The potential of the electrochemical way. International Journal of Electrochemical Science, Vol 9. 3449--3457.Google ScholarCross Ref
- Reyes, P.I. 2011. ZnO thin film transistor immunosensor with high sensitivity and selectivity. Applied Physics Letters. 98(17). 173702--173704.Google ScholarCross Ref
- Beyette, F.R. 2011. Point-of-Care technologies for Health Care. IEEE Transactions on Biomedical Engineering. 58(3). Pages 732--735.Google ScholarCross Ref
- Hubalek, J. 2009. New Approach in Rapid Viruses Detection and its Implementation on a Chip. Presented at International Conference on eHealth, Telemedicine, and Social Medicine, Cancun Mexico, 108--112. Google ScholarDigital Library
- Lopez, C.A. 2013. An interferometric reflectance imaging sensor for point of care viral diagnostic. IEEE transactions on biomedical engineering. Vol. 60(12). 3276--3283.Google Scholar
- Massicotte, G., Carrara, S., Di Micheli, G., and Sawan, M. 2016. A CMOS amperometric system for multi-neurotransmitter detection. IEEE Transactions on Biomedical Circuits and Systems, Vol. 10, No. 3, 731--741.Google ScholarCross Ref
- Jung,S-J., Hong,S-K., and Kwon, O-K. 2016. A readout IC using two-step fastest signal identification for compact data acquisition of PET systems. Sensors, Vol. 16(10), 1748.Google ScholarCross Ref
- Suliman, A. and Nazeri, S., 2014. The Evaluation of an embedded system Kit As A C programming teaching Tool, Journal of ICT, 13, 123--138.Google Scholar
- Knight, J. Dependability of Embedded Systems. 2002. ICSE '02 Proceedings of the 24th International Conference on Software Engineering. 685--686. Google ScholarDigital Library
Index Terms
- Design of Embedded System for Electrochemical Immunosensor Using NI myRIO
Recommendations
Electrochemical polishing of ITO films
Oxalic acid and tartaric acid were used to electrochemically treat the surface of indium tin oxide (ITO) films. To improve the surface of ITO films, the applied voltage was found via potentiodynamic technique. By controlling the concentration of oxalic ...
Enhancing electrochemical performance of silicon anodes by dispersing MWCNTs using planetary ball milling
Graphical abstractDisplay Omitted Highlights Si/MWCNT nanocomposite anodes were produced by high energy mechanical milling method. Increasing MWCNTs in the nanocomposite leads to create a network like structure. Typical reflection peaks of silicon and ...
Electrochemical-mechanical polishing application: Monitoring of electrochemical copper removal from current-voltage characteristics in HNO3 electrolyte
Recently, electrochemical-mechanical polishing (ECMP) has been suggested as an alternative to the conventional chemical-mechanical polishing (CMP) process. In ECMP process, copper (Cu) ions are electrochemically dissolved by applying an anodic potential ...
Comments